Smart Garage Door Opener Cost Guide
Smart control prices as two different purchases: a full smart opener that replaces the unit on the ceiling, or a retrofit hub that adds app control to the opener already there. Angi 2026 reporting prices smart openers and controllers at $25 to $400 or more, with hubs starting at $25. This guide prices both lanes apart.
Orange County, CA · Updated 2026 · Costs shown as ranges — your quote will vary by installer and scope
The Angi smart frame, named apart and never blended
| Smart purchase | Angi 2026 figure | What it prices |
|---|---|---|
| Smart openers and controllers | $25-$400+ | the whole smart band |
| Hub attachment | starting at $25 | control added to an existing opener |
| Full smart system | upwards of $400 | motor, rail, transmitter, and app together |
| Fully featured unit | $400-$600 | camera, battery backup, and keypad included |
The Angi frame draws the split itself: a hub is an attachment priced from $25, while a full system carries the motor and rail and prices upwards of $400. The two ends of the band are not averages of each other. The standard version of the full purchase prices on the garage door opener installation cost hub.
The retrofit hub lane, in retail reporting
Retail reporting prices the hub lane as its own small purchase. Basic retrofit controllers are reported at $30 to $80, and add-on smart controllers at $29 to $99, bands that keep the existing motor, drive, and rail in place and add a controller plus a door sensor as the priced parts. The lane prices apart from the Angi frame above because it is reported at retail, as a product band rather than a project band. A hub on an opener near the end of its reported span is a different decision, priced on the garage door opener repair vs. replacement cost guide.
The full smart opener lane, installed
A full smart opener prices inside the same two installation frames, named apart. In the Angi frame, professional installation runs $220 to $540, average around $380, with the unit at $150 to $600. In the HomeGuide frame, the installed purchase runs $300 to $900, average $600, with the unit at $150 to $500 by drive type. The Angi smart frame prices fully featured units, camera, battery backup, and keypad included, at $400 to $600. Read the smart premium inside one frame only, never across frames.
The add-on layer, as reported cost lines
| Add-on line | Angi 2026 figure | Frame note |
|---|---|---|
| Battery backup | $50-$150 | Angi parts pricing |
| Sensor pair, parts line | $50-$100 | Angi parts pricing |
| Sensor pack of two | $25-$50 | Angi reported line |
| Automatic lock | $100-$300 | Angi parts pricing |
Add-ons price as parts lines on top of either lane. Battery backup is the line both lanes quote most often, at $50 to $150 in the Angi parts frame. Keypad and camera features price two ways in the reporting: folded into the fully featured unit band at $400 to $600, or as accessory lines on a plainer unit. A quote should state which way each feature is priced, and no add-on line here carries an installation procedure of any kind, only its reported price.
How this guide differs from the hub and the decision guide
The garage door opener installation cost hub prices standard opener installation by drive type, with no smart layer. This guide prices only the connected purchases: the retrofit hub and the full smart unit. The garage door opener repair vs. replacement cost guide prices fixing the current unit against replacing it; this guide assumes the smart feature set is the reason for the purchase and prices what that feature set costs in each lane. Three guides, three questions: install it, fix or replace it, or connect it.
- Lane named on the quote: hub or full unit
- Frame named: Angi, HomeGuide, or retail reporting
- Existing motor and rail kept, or replaced
- Battery, keypad, and camera lines shown apart
- Smart premium read inside one frame only
Frequently asked questions
How much does a smart garage door opener cost?
Angi 2026 frame: smart openers and controllers $25 to $400 or more, with fully featured units at $400 to $600. Installed, a full smart opener prices inside the hub frames: Angi $220 to $540, HomeGuide $300 to $900. The frames are named apart.
What does a retrofit smart hub cost?
Retail reporting prices basic retrofit controllers at $30 to $80 and add-on smart controllers at $29 to $99. The Angi frame prices hub attachments starting at $25. The hub keeps the existing motor and rail, so no installation frame attaches to it.
What do smart add-ons cost on top of an opener?
In the Angi parts frame: battery backup $50 to $150, a sensor pair $50 to $100, a sensor pack of two $25 to $50, and an automatic lock $100 to $300. Keypad and camera features also price folded into fully featured units at $400 to $600.
Is a full smart opener priced like a standard opener?
The installed frames are the same two, named apart: Angi $220 to $540 and HomeGuide $300 to $900. The difference sits in the unit line, where the Angi smart frame prices fully featured units at $400 to $600.
Does adding a hub replace the opener?
No. The hub is priced as an attachment to the opener already installed, controller and door sensor only, at $25 upward in the Angi frame. A full smart opener replaces the unit and prices as an installation.