Insulation Removal Cost by Type Guide
The type layer prints apart by frame: blown-in sits near the low end of each per-foot band and rigid near the top, with a project total for each type on each frame.
Orange County, CA · Updated 2026 · Costs shown as ranges — your quote will vary by installer and scope
The type layer, priced apart
| Frame | Type line, as published | 2026 band, per project |
|---|---|---|
| Frame A | blown-in removal | $600-$1,000 |
| Frame A | batts and rolls removal | $800-$1,100 |
| Frame A | rigid removal | $900-$1,200 |
| Frame B | rigid removal | $1,200-$2,200 |
Every figure here is a published line inside its own frame, never averaged into one band. Type is the first attribute both frames name on this layer. The project whole prices on the insulation removal hub; the breakdown layer on the breakdown guide.
Frame A type lines, as reported
| Type line, as published | Type, as described | 2026 band, per project |
|---|---|---|
| Blown-in | cellulose, fiberglass, and rock wool, vacuum removal | $600-$1,000 |
| Batts and rolls | fiberglass, rock wool, and natural fibers, hand removal | $800-$1,100 |
| Rigid | foam boards and spray foams, hand removal | $900-$1,200 |
Frame A's type table prints each type as a project total inside its $1 to $2 per-square-foot band: blown-in near the low end of that band and rigid near the top, as its article states the order. The rigid line carries the highest total of the three; the blown-in line prints the lowest; batts and rolls sit between them. No type total is added into a new total on this page.
Frame B type lines, as reported
| Type line, as published | Reading | 2026 band, per project |
|---|---|---|
| Blown-in | Los Angeles metro frame | $800-$1,400 |
| Batts and rolls | Los Angeles metro frame | $1,000-$1,800 |
| Rigid | Los Angeles metro frame | $1,200-$2,200 |
| Any type, per square foot | Los Angeles metro frame | $1.80-$3.50 |
Frame B prints the same three types in the same order at its metro reading: blown-in lowest, batts and rolls in the middle, rigid highest, each total above its Frame A counterpart. The ordering is shared; the counting region is not, and no Frame B total is restated on Frame A's terms here.
Reading the same type on both frames, as reported
| Reading, as published | Frame | 2026 band, per project |
|---|---|---|
| Blown-in removal | Frame A | $600-$1,000 |
| Blown-in removal | Frame B | $800-$1,400 |
| Rigid removal | Frame A | $900-$1,200 |
| Rigid removal | Frame B | $1,200-$2,200 |
The same type word appears on both frames and means a different count on each. On Frame A, the word names one type total inside a national frame; on Frame B, it names the same type inside a California-metro frame. This guide keeps those readings on separate lines, and neither reading is converted into the other.
Reading a by-type quote, by frame
A type line answers the type question: blown-in, batts and rolls, or rigid. A quote names its type in its first line and its frame beside it, and its project total apart from any per-foot reading.
- Type named beside every band
- Project totals read apart from per-foot lines
- Each frame's type reading read on its own frame only
Frequently asked questions
How much does blown-in insulation removal cost, as published?
Frame A prints blown-in removal at $600 to $1,000 per project, near the low end of its $1 to $2 per-square-foot band. Frame B prints blown-in at $800 to $1,400 per project in its Los Angeles metro frame, at $1.80 to $3.50 per square foot.
What do batts and rolls cost to remove, as reported?
Frame A prints batts and rolls at $800 to $1,100 per project, between its blown-in and rigid lines. Frame B prints batts and rolls at $1,000 to $1,800 per project, in the same middle position on its metro frame.
Which type line prints highest on both frames, as reported?
Rigid, on both frames. Frame A prints rigid removal at $900 to $1,200 per project, near the top of its per-foot band. Frame B prints rigid at $1,200 to $2,200 per project, the highest of its three type lines as well.
Does the type order change between the two frames, as reported?
No. Both frames print the same order, lowest to highest: blown-in, then batts and rolls, then rigid. What changes is the counting region -- a national frame against a California-metro frame -- and the totals that sit on each frame.
Can a Frame A type total be combined with a Frame B per-foot band?
No. Frame A counts one type total at a time inside its national frame and Frame B counts its metro reading by the foot and by the project. The frames and their type readings are never blended, no type total is summed into a new total here, and neither band is converted into the other.